+91 0771-2533510 +91 82245-19999 support@zarpaints.com

MAGIC SILK EMULSION is a luxurious water base acrylic emulsion specially formulated to provide high sheen and luxury effect for interior surfaces.

It is a luxurious finish which can be applied on interior cement plasters, ceilings, asbestos sheets, concrete, etc., as a top coat.

  • High Sheen
  • Luxurious Finish
  • High Colour Depth and Opacity
  • Stain Resistant and Easy Clean
  • Excellent Coverage with Soft Silky Imparts Pearl Like Glow to Walls

Spray, Brush or Roller

  • APPLICATION : Spray, Brush, Roller
  • RECOMMENDED DFT : 30 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 28 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 1 hrs
  • HARD DRY : Within 4 hrs
  • COLOUR : White, Assorted
  • FINISH : High Sheen
  • OVERCOAT INTERVAL : Min 4 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 30 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 4 Ltrs.
  • 1 Ltr.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Cement Primer should be applied. Surface thus prepared is ready for application of MAGIC Silk Interior Emulsion. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 40 % by volume depending upon the surface. Apply two coats at interval of 4 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.

MAGIC SMART EMULSION is a luxurious water base acrylic emulsion specially formulated to provide high sheen and luxury effect for interior surfaces.

It is a luxurious finish which can be applied on interior cement plasters, ceilings, asbestos sheets, concrete, etc., as a top coat.

  • High Sheen
  • Luxurious Finish
  • High Colour Depth and Opacity
  • Stain Resistant and Easy Clean
  • Excellent Coverage with Soft Silky Feel
  • Imparts Pearl Like Glow to Walls.

Spray, Brush or Roller

  • APPLICATION : Spray, Brush, Roller
  • RECOMMENDED DFT : 30 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 28 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 1 hrs
  • HARD DRY : Within 4 hrs
  • COLOUR : White, Assorted
  • FINISH : High Sheen
  • OVERCOAT INTERVAL : Min 4 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 30 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 4 Ltrs.
  • 1 Ltr.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Cement Primer should be applied. Surface thus prepared is ready for application of MAGIC Silk Premium Acrylic Emulsion. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 40 % by volume depending upon the surface. Apply two coats at interval of 4 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.

MAGIC SMOOTH EMULSION is an economical co-polymer water base acrylic emulsion specially formulated for interior surfaces.

It can be applied on exterior cement plasters, asbestos sheets, concrete, etc., as a top coat.

  • Excellent Coverage
  • Anti Fading Colours
  • Resistant to Fungus and Algae
  • UV Resistant
  • Low Dirt Pick Up
  • Fantastic Durability as it is Peel Resistant

200 Sq. Ft. / Coat

Spray, Brush or Roller

  • APPLICATION : Spray, Brush, Roller
  • RECOMMENDED DFT : 30 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 28 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 1 hrs
  • HARD DRY : Within 3 hrs
  • COLOUR : White, Assorted
  • FINISH : Matt
  • OVERCOAT INTERVAL : Min 3 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 40 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 4 Ltrs.
  • 1 Ltr.
  • 500 ML.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Exterior Wall Primer should be applied. Surface thus prepared is ready for application of MAGIC XT Prue Acrylic Emulsion. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 40 % by volume depending upon the surface. Apply two coats at interval of 3 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.

**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.

Magic silk sparkle is a high sheen metallic emulsion which is used to give textured effect to walls.

It is used to impart a metallic look to the wall. It is well suited for wood, POP and other types of interior design accessories.

  • High Sheen
  • Luxurious Finish
  • High Colour Depth and Opacity
  • Stain Resistant and Easy Clean
  • Excellent Coverage with Soft Silky Imparts Pearl Like Glow to Walls

Brush, roller or sponge

  • APPLICATION : Spray, Brush, Roller
  • RECOMMENDED DFT : 30 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 28 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 1 hrs
  • HARD DRY : Within 4 hrs
  • COLOUR : White, Assorted
  • FINISH : High Sheen
  • OVERCOAT INTERVAL : Min 4 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 30 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

Gold & Silver

  • 20 Ltrs.
  • 10 Ltrs.
  • 4 Ltrs.
  • 1 Ltrs.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Cement Primer should be applied. Surface thus prepared is ready for application of MAGIC Silk sparkle. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 40 % by volume depending upon the surface. Apply two coats at interval of 4 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.

MAGIC PREMIUM ACRYLIC DISTEMPER is an economical acrylic coating supplied in paste form specially for interior surfaces.

It is an excellent Acrylic coating in paste form which can be applied on a wide range of Interior Cement Plasters, Ceilings, Asbestos Sheets, Concrete, etc., as a Top Coat Finish.

  • Economical
  • Durable and soft finish.
  • Ease of Application
  • Good Washablity

Spray, Brush or Roller

  • APPLICATION : Spray, Brush, Roller
  • RECOMMENDED DFT : 45 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 17 M2/Ltr/Coat*
  • DRYING – SURFACE DRY :Within 30 minutes
  • HARD DRY : Within 4 hrs
  • COLOUR : White, Assorted
  • FINISH : Matt
  • OVERCOAT INTERVAL : Min 4 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 60 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 5 Ltrs.
  • 2 Ltrs.
  • 1 Ltr.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Cement Primer should be applied. Surface thus prepared is ready for application of MAGIC Premium Acrylic Distemper. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 60 % by weight depending upon the surface. Apply two coats at interval of 4 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight

AJOOBA ACRYLIC DISTEMPER is an economical acrylic coating supplied in paste form especially for interior surfaces.

It is an economical Acrylic coating in paste form which can be applied on a wide range of Interior Cement Plasters, Ceilings, Asbestos Sheets, Concrete, etc., as a Top Coat Finish.

  • Very Economical
  • Pleasant Matt Finish
  • Ease of Application
  • Decent Washablity

Spray, Brush, Roller

  • APPLICATION : Spray, Brush, Roller
  • RECOMMENDED DFT : 48 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 15 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 30 minutes
  • HARD DRY : Within 4 hrs
  • COLOUR : White, Assorted
  • FINISH : Matt
  • OVERCOAT INTERVAL : Min 4 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 60 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 5 Ltrs.
  • 2 Ltrs.
  • 1 Ltr.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Cement Primer should be applied. Surface thus prepared is ready for application of AJOOBA Acrylic Distemper. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 60 % by weight depending upon the surface. Apply two coats at interval of 4 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight