+91 0771-2533510 +91 82245-19999 support@zarpaints.com

MAGIC ULTIMAX EMULSION is a premium acrylic water base emulsion specially formulated to provide high sheen and protection for exterior surfaces.

It is a hi sheen coating which can be applied on exterior cement plasters, asbestos sheets, concrete, etc., as a top coat.

  • Elastomeric Film Covers Hair-Line Cracks
  • High Sheen
  • Excellent Coverage
  • Fantastic Durability
  • Anti Fading Colours
  • UV Resistant
  • Low Dirt Pick Up
  • Weather Resistant
  • Water Repellent and Self Cleaning
  • Provides good insulation that lowers the interior temperature

Spray, Brush or Roller

  • APPLICATION : Spray, Brush, Roller
  • RECOMMENDED DFT : 30 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 28 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 1 hrs
  • HARD DRY : Within 4 hrs
  • COLOUR : White, Assorted
  • FINISH : High Sheen
  • OVERCOAT INTERVAL : Min 4 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 30 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 4 Ltrs.
  • 1 Ltr.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Exterior Wall Primer should be applied. Surface thus prepared is ready for application of MAGIC ULTIMAX Premium Acrylic Emulsion. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 30 % by volume depending upon the surface. Apply two coats at interval of 4 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade. **As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.

MAGIC XT MAX EMULSION is a premium acrylic water base emulsion specially formulated to provide smooth and matt finish for exterior surfaces.

It can be applied on exterior cement plasters, asbestos sheets, concrete, etc., as a top coat.

  • Excellent Coverage
  • Anti Fading Colours
  • Resistant to Fungus and Algae
  • UV Resistant
  • Low Dirt Pick Up
  • Fantastic Durability as it is Peel Resistant

Air Spray, Brush, Roller

  • APPLICATION : Air Spray, Brush, Roller
  • RECOMMENDED DFT : 38 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 17 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 1 hrs
  • HARD DRY : Within 3 hrs
  • COLOUR : White, Assorted
  • FINISH : Matt
  • OVERCOAT INTERVAL : Min 3 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 40 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 4 Ltrs.
  • 1 Ltr.
  • 500 ML.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Exterior Wall Primer should be applied. Surface thus prepared is ready for application of MAGIC XT MAX Prue Acrylic Emulsion. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 40 % by volume depending upon the surface. Apply two coats at interval of 3 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.

**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.

MAGIC XT EMULSION is a premium acrylic water base emulsion specially formulated to provide smooth and matt finish for exterior surfaces.

It can be applied on exterior cement plasters, asbestos sheets, concrete, etc., as a top coat.

  • Excellent Coverage
  • Anti Fading Colours
  • Resistant to Fungus and Algae
  • UV Resistant
  • Low Dirt Pick Up
  • Fantastic Durability as it is Peel Resistant

200 Sq. Ft. / Coat

Spray, Brush or Roller

  • APPLICATION : Spray, Brush, Roller
  • RECOMMENDED DFT : 30 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 28 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 1 hrs
  • HARD DRY : Within 3 hrs
  • COLOUR : White, Assorted
  • FINISH : Matt
  • OVERCOAT INTERVAL : Min 3 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 40 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 4 Ltrs.
  • 1 Ltr.
  • 500 ML.

Clean the surface thoroughly using wire brush and sand paper. All fungus and algae affected area should be cleaned by anti fungicidal solution. Surface Imperfections should be dealt with by applying MAGIC ROCK HARD Wall Putty after which a coat of MAGIC Exterior Wall Primer should be applied. Surface thus prepared is ready for application of MAGIC XT Prue Acrylic Emulsion. Stir thoroughly before application. Material is supplied ready to use but can be thinned by water up to 40 % by volume depending upon the surface. Apply two coats at interval of 3 to 6 hours between the two coats.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.

**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.

It is white cement based economic exterior wall finish. It can be applied as top coat.

Hard durable water proof finish, Excellent light reflection, anti fungus and anti algal

Brush or Roller

80 Sq. Ft./ Coat

25 KG.

Magic Sand Texture is a pigmented decorative thick textured wall finish which has quartz powder and marble chips which gives it a rough cast appearance.

Gives a out of the box effect, weather resistant, high strength, designer effect.

30 Sq. Ft. / Coat

Spray, Brush or Roller

MAGIC CEM PLUS is an economic exterior wall finish designed to giv protection against varying whether conditions. It is a water dispersible coating having antifungal & anti-algael properties.

It can be applied on exterior cement plasters, asbestos sheets, concrete, etc., as a top coat.

  • Excellent Coverage
  • Anti Fading Colours
  • Resistant to Fungus and Algae
  • UV Resistant
  • Low Dirt Pick Up
  • Fantastic Durability as it is Peel Resistant

Air Spray, Brush, Roller

  • APPLICATION : Air Spray, Brush, Roller
  • RECOMMENDED DFT : 38 microns
  • THEORETICAL SPREADING RATE AT ABOVE DFT : 17 M2/Ltr/Coat*
  • DRYING – SURFACE DRY : Within 1 hrs
  • HARD DRY : Within 3 hrs
  • COLOUR : White, Assorted
  • FINISH : Matt
  • OVERCOAT INTERVAL : Min 3 hrs Max None
  • FLASH POINT : Non Combustible
  • THINNER : 40 % by Volume with Water
  • SHELF LIFE : 3-4 Years**

White & All Other Shades

  • 20 Ltrs.
  • 10 Ltrs.
  • 4 Ltrs.
  • 1 Ltr.
  • 500 ML.

For excellent bonding results, rub in the first coat with a short stiff or fibre bristied brush. Cure the surface thoroughly with a spray of water, 6-8 hours after the first coat. Apply the second coat only 24 hours after the first coat and the water has completely runoff the surface. Sprinkle surface with water, 2-3 times a day for atleast 2 days. Due care should be given to the curing process to prevent chalking. Avoid working in direct sunlight or dry wind.

As a general rule, avoid inhalation of paint mist and contact of paint with skin and eyes. Provide forced ventilation when working in confined spaces or stagnant air. Also provide respiratory, skin and eye protection. Do not allow Kids to come near the paint. Also follow local and national safety regulations.

*Actual covering capacity may vary depending upon the method & condition of application, surface condition, temperature, wind velocity, application skills, surface roughness, surface porosity & shade.**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.

**As long as the containers is sealed and kept at normal temperature without any direct exposure to sunlight.